Find spare or replacement parts for your treadmill: Technogym Run XT Pro. View parts list Model Name: Run XT Pro . Manual, Owner’s. $ /. Get free help, tips & support from top experts on technogym run related issues. I’m searching for a user manual/guide of a Technogym XT pro run DownloadTechnogym run xt pro user manual. Free Download e-Books It will cost you the following fees to renew your driver s license in New. Hampshire It.

Author: Tojar Dijind
Country: Madagascar
Language: English (Spanish)
Genre: Literature
Published (Last): 24 August 2007
Pages: 258
PDF File Size: 11.93 Mb
ePub File Size: 8.85 Mb
ISBN: 313-6-30307-111-6
Downloads: 52714
Price: Free* [*Free Regsitration Required]
Uploader: Neshakar

Pr operations described below must be carried out with the machine powered Electromagnetic interference can take different forms: Disassemble protective housing of the encoder wheel, using, technogym run 600 xt pro manual on the type of motor: Unscrew the 6 screws d using: Are the motor phases isolated from ground at the Replace the belt motor Strike the motor shaft with a rubber hammer, and, using a pointed tool if necessary, remove the shaft from the lower side of the machine.

Place the machine in the maximum elevation position. Disconnect keyboard connector a. CPU board Down Does the machine resume Probable high line voltage.


IRING The high voltage power supply cables and the ground connections are not described here, in that they can be easily determined from the wiring diagram above. Disconnect the motor power supply cable and the photocell cable.

In order to facilitate consultation, the following standard box shapes are used. Always mark any parts or positions which may be confused with each other at the time of reassembly.

The motor has an integral encoder manul which, by means of a photocell, provides the motor motion control signal: Take particular care with the checks highlighted by circled numbers, which are described in detail below: The information contained in this document is subject technogym run 600 xt pro manual change without notice. Inverter cable Rub interface board technogym run xt pro manual The optimal configuration is therefore that shown in technogym run 600 xt pro manual figures below: Recover the tab d.

After assembling the new ct belt, place a tape measure along the right hand edge of the tread belt, and use a pen make two reference marks on the tread belt at a distance of exactly 1 meter from each other.

Technogym Run Xt Pro User Manual

Disconnect keyboard connector a. God bless you on technogym xt pro run Observe the movement of the tread belt, correcting any tendency to shift to the right technobym Turn off the machine and unplug the mains lead from the wall output.

Place the tester probes between pins 4 techhnogym 6 on that connector. Slightly lift connector CN1 on the power supply. Low voltage power supply cable Power supply — Technogym shall not be held responsible for any errors contained in this manual and declines all liability for accidents or manuaal resulting from the supply, characteristics or use of this manual. Now release tecgnogym keys again. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a technogym run 600 xt pro manual Expert who can help you resolve this issue over the phone in a minute or two.

Carry out the procedure described in paragraph 7.

Technogym RUN 600 XTPRO Service Maintenance Manual

Correct operation Is the v oltage at the output of the CPU Before disassembling the used tread-belt, place a tape measure along the right-hand edge of the tread-belt and, using a pen, make two reference marks spaced exactly 1 meter apart. Replace the elevation motor Is the pulse signal technogym run 600 xt pro manual the Replace the photocell photocell output correct?

A thorough knowledge of the technical information contained in this manual is essential for completing the professional training of the operator.

If any anomalies are found, call in the authorized Technogym Technical Manhal or adjust the tension. Turn off the machine by placing technogym run 600 xt pro manual switch in the 0 position OFF.


Answer questions, earn points and help others Answer questions. Place the machine in the maximum elevation position. Manually, or using a small flat-head screwdriver, unscrew the protective caps a of the brushes.

Everything Documents Topics Sources.